S136 vs. NAK80 for Optical Molds: A Decision Guide
Most S136-vs-NAK80 comparisons lead with corrosion resistance — a valid consideration for PVC or certain flame-retardant resins. Optical-grade PMMA, PC, and COC are generally non-corrosive. Here’s what actually determines the choice when resin corrosion is not a concern.
Nearly every S136-vs-NAK80 comparison online opens with corrosion resistance as the deciding factor — a real and important consideration for PVC, acetate, or certain flame-retardant resin molds. But optical-grade PMMA, PC, and COC/COP are generally non-corrosive materials. For a lens mold running these materials, the corrosion-resistance considerations emphasized in general steel-selection guides are typically less relevant. The decision instead comes down to factors such as achievable mirror-polish quality, dimensional stability, and lead time.
Walk Through the Decision
Why Corrosion Resistance Usually Isn’t the Deciding Factor Here
S136’s defining advantage — its high chromium content and resistance to pitting from corrosive off-gassing — addresses a problem associated with PVC, acetate, and certain flame-retardant compounds but generally not with PMMA, PC, or COC/COP. Specifying S136 primarily for corrosion resistance when molding a non-corrosive optical resin can add tooling cost (S136 typically requires hardening and may carry a higher, more variable cost than NAK80) without addressing a significant application risk.
Mirror Polish: Where the Real Optical Difference Shows Up
Both steels can achieve a genuine mirror finish, but their achievable polishing levels differ. Reported polishing data places NAK80 at roughly #10,000–12,000 grit, while properly hardened S136 — particularly ESR-grade material — can reach #12,000–18,000 grit, with surface roughness reaching approximately 0.01–0.012 μm Ra in demanding applications. For most commercial and industrial optical lenses, NAK80’s polish ceiling is more than sufficient. The difference matters most for demanding surface-finish and surface-figure requirements — such as laser optics and high-end imaging systems — where the additional polishing capability of S136 ESR can justify the higher material specification.
Dimensional Stability: NAK80’s Structural Advantage
NAK80 is supplied pre-hardened and does not require post-machining heat treatment, avoiding a potential source of geometric distortion associated with the heat treatment of steels such as S136. For tight-tolerance optical geometries — where the tolerance budgets covered in our optical lens tolerances guide leave little room for mold-induced deviation — this can be a more practically relevant advantage than the difference in polishing capability.
| Factor | S136 | NAK80 |
|---|---|---|
| Corrosion resistance | High — needed for corrosive resins | Low — generally not a concern for optical PMMA/PC/COC |
| Mirror polish ceiling | Highest tier (ESR grade), #12,000–18,000 grit | Strong standard tier, #10,000–12,000 grit |
| Heat treatment | Required post-machining — warpage risk | Pre-hardened — avoids post-machining heat-treatment distortion |
| Typical cost/lead time | Higher, more variable | More stable, often faster |

Frequently Asked Questions
Is S136 always the “better” steel for optical lens molds?
No. S136’s core advantage is corrosion resistance, which matters for corrosive resins like PVC or flame-retardant compounds. Optical-grade PMMA, PC, and COC/COP are generally non-corrosive, so for most optical lens programs, NAK80 can provide sufficient mirror-polish capability and good dimensional stability, often at lower cost and with a shorter lead time.
When does S136 make sense for an optical mold?
S136, particularly ESR grade, can justify its cost premium when a program requires the highest mirror-polish quality — such as laser optics or high-end imaging systems with sub-10 nm Ra requirements — or when the resin itself is corrosive, which is uncommon for standard optical lens materials.
Does NAK80’s lack of heat treatment actually matter for tolerance?
Yes, for tight-tolerance geometries. Heat treatment can introduce dimensional distortion in hardened steels. Since NAK80 is pre-hardened and does not require this additional heat-treatment step, it avoids this particular source of distortion — often a more practically important factor than the difference in polishing capability versus S136.
Supplier Checklist
- Does the supplier default to S136 regardless of resin, or actually assess whether corrosion resistance applies to your material?
- What grit/Ra polish level do they commit to in writing for your specific steel choice?
- For NAK80 tooling, what pre-hardened HRC range do they specify?
- For S136 tooling, is it ESR grade, and is that reflected in the quote?
- Can they explain the tradeoff between tolerance requirements and steel selection for your specific lens geometry?
Most S136-vs-NAK80 content available online is written for the general injection molding market, where corrosive resins are common enough to make corrosion resistance a natural starting point. Optical lens programs running PMMA, PC, or COC/COP generally fall outside that assumption — which is why applying a generic steel-selection guide to an optical mold program can lead to over-specifying S136 for a property the application may not require.
Specifying Mold Steel for an Optical Lens Program?
Talk to our mold engineering team about steel selection matched to your actual resin, tolerance, and polishing requirements — not a default specification.
Request a Technical Consultation